&

國外無損檢測標準

2022-08-05 10:51:47 作者：工業小南點來源：工業小南點分享至：

歐洲標準化委員會標準：

EN 1290:1998 焊縫無損檢測焊縫的磁粉檢驗

Non-destructive examination of welds-Magnetic particle examination of welds

EN 1291:1998 焊縫無損檢測焊縫的磁粉檢驗驗收等級

Non-destructive examination of welds-Magnetic particle testing of welds-Acceptancelevels

EN 1330/5:1998 無損檢測詞匯渦流檢測所用術語

Non-destructive testing-Terminology-Part 5:Terms used in Eddy current testing

EN 1369:1996 鑄件磁粉檢查

EN 1711:2000 焊縫無損檢測基于復平面分析的焊縫渦流檢測

Non-destructive examination of welds-Eddy current examination of welds by complexplane analysis

EN 1956: 無損檢測滲透檢測和磁粉檢測

EN 1971: 銅和銅合金的渦流檢測

EN 2857/1: 磁粉檢測總則

EN 2857/2: 檢查要求

EN ISO 3059:2001 無損檢測滲透檢測和磁粉檢測觀察條件

Non-destructive testing-Penetrant testing and magnetic particle testing-Viewingconditions(ISO 3059:2001)

EN ISO 9934-1:2001/A1:2003 無損檢測磁粉檢測第1部分：一般原理

Non-destructive testing-Magnetic particle testing-Part 1:General principles(ISO9934-1:2003)

EN ISO 9934-2:2002 無損檢測磁粉檢測第2部分：檢測介質

Non-destructive testing-Magnetic particle testing-Part 2:Detection media(ISO9934-2:2002)

EN ISO 9934-3:2002 無損檢測磁粉檢測第3部分：設備

Non-destructive testing-Magnetic particle testing-Part 3:Equipment(ISO9934-3:2002)

EN 10228/1:1999 磁粉檢查

EN 10246/1:1996 無縫與焊接（埋弧焊除外）鐵磁性鋼管的自動電磁檢測-驗證液壓密封性

EN 10246/2:2000 無縫與焊接（埋弧焊除外）奧氏體和奧氏體鐵素體鋼管的自動渦流檢測-驗證液壓密封性

EN 10246/3:1999 無縫與焊接（埋弧焊除外）鋼管的自動渦流檢測-探傷

EN 10246/4:1999 無縫鐵磁性鋼管的自動全圓周磁傳感器/漏磁檢測-檢測橫向缺陷

EN 10246/5:1999 無縫與焊接（埋弧焊除外）鐵磁性鋼管的自動全圓周磁傳感器/漏磁檢測-檢測縱向缺陷

EN 10246/12:2000 無縫與焊接鐵磁性鋼管的磁粉檢測-檢測表面缺陷

EN 10246/18:2000 無縫與焊接鐵磁性鋼管管端面的磁粉檢測-檢測層狀缺陷

EN 12084:2001/A1:2003 無損檢測渦流檢測一般原理和指南

Non-destructive testing-Eddy current testing-General principles and guidelines

EN 13860-1:2003 無損檢測渦流檢測設備性能與驗證第1部分：儀器性能與驗證

Non-destructive testing-Eddy current examination-Equipment characteristics andverification-Part 1:Instrument characteristics and verification

EN 13860-2:2003 無損檢測渦流檢測設備性能與驗證第2部分：探頭性能與驗證

Non-destructive testing-Eddy current examination-Equipment characteristics andverification-Part 2:Probe characteristics and verification

EN 13860-3:2003 無損檢測渦流檢測設備性能與驗證第3部分：系統性能與驗證

Non-destructive testing-Eddy current examination-Equipment characteristics andverification-Part 3:System characteristics and verification

EN WI 45:2002 渦流檢測設備

03014008發表于 2008-11-812:54

美國標準：

ASTM A275/A275M-1998 鋼鍛件磁粉檢驗方法(A-1) Test Method for Magnetic Particle Examination of SteelForgings

ASTM A340-2001 與磁化試驗有關的符號和定義的術語

Terminology of Symbols and Definitions Relating to Magnetic Testing

ASTM A341/A341M-1995 用直流磁導計和彈道學法測定材料直流磁性能的試驗方法

Test Method for Direct Current Magnetic Properties of Materials Using D-CPermeameters and the Ballistic Test Methods

ASTM A342-1995 弱磁材料導磁率的試驗方法 Test Methods forPermeability of Feebly Magnetic Materials

ASTM A450-76 鋼管渦流檢測

ASTM A456/A 456M-1999 大型曲軸鍛件磁粉檢驗的標準規范

Standard Specification for Magnetic Particle Examination of Large CrankshaftForgings

ASTM A556-65 無縫碳素鋼管渦流檢測

ASTM A596/A596M-1995 用彈道學法和環形試樣測定材料直流磁性能的試驗方法

Test Method for Direct-Current Magnetic Properties of Materials Using theBallistic Method and Ring Specimens

ASTM A772/A772M-1995 利用正弦電流測定材料交流磁導率的試驗方法

Test Method for A-C Magnetic Permeability of Materials Using Sine Current

ASTM A894/A894M-1995 磁性材料飽和磁化的試驗方法 Test Method for Saturation Magnetization of Magnetic Materials

ASTM A 903/A 903M-1999 鋼鑄件磁粉和液體滲透檢驗的表面驗收標準

Steel Castings, Surface Acceptance Standards, Magnetic Particle and LiquidPenetrant Inspection

ASTM A966-1996 用交流電流檢驗鋼鍛件磁粉檢驗方法

Test Method for Magnetic Particle Examination of Steel Forgings UsingAlternating Current

ASTM A977-1997 使用磁滯曲線繪制儀測試高矯頑磁性永磁材料磁性能的標準試驗方法

Standard Test Method for Magnetic Properties of High-Coercivity PermanentMagnet Materials Using Hysteresigraphs

ASTM B193-1995 導電材料電阻率的測試方法 Test Method for Resistivityof Electrical Conductor Materials

ASTM B244-1997 用渦流儀測量鋁陽極化層及其它非磁性金屬基體上絕緣涂層的厚度

Measurement of Thickness of Anodic Coatings on Aluminum and of OtherNonconductive Coatings on Nonmagnetic Basis Metals with Eddy-CurrentInstruments

ASTM B342-70 材料導電率的渦流測量方法

ASTM B499-1996 磁性金屬基體上非磁性涂層厚度測量的試驗方法：磁性法(B-8)

Test Method for Measurement of Coating Thicknesses by the Magnetic Method:Nonmagnetic Coatings on Magnetic Basis Metals

ASTM B529-70 非磁性金屬上非導電層厚度的渦流測量方法

ASTM B530-1996 用磁性法測量磁性和非磁性基體上的電鍍鎳層厚度的試驗方法

Test Method for Measurement of Coating Thicknesses by the Magnetic Method:Electrodeposited Nickel Coatings on Magnetic and Nonmagnetic Substrates

ASTM B554-71 非金屬上金屬涂層厚度測量的推薦方法

ASTM C1238-1997 地下通道金屬探測器的安裝 Installation ofWalk-Through Metal Detectors

ASTM C1269-1997 內穿過式金屬探測器操作靈敏度設置調整的標準規程

Standard Practice for Adjusting the Operational Sensitivity Setting of In-PlantWalk-Through Metal Detectors

ASTM C1309-1997 內穿過式金屬檢測器性能評定的標準規程

Standard Practice for Performance Evaluation of In-Plant Walk-Through MetalDetectors

ASTM D1186-93 鐵基體上非磁性薄膜的干膜厚度無損測量方法

ASTM D1400-94 非鐵金屬基體上非導電覆蓋層干膜厚度無損測量方法

ASTM D4166-1999 數字磁強儀測量非磁性材料厚度的試驗方法

Test Method for Measurement of Thickness of Nonmagnetic Materials by Means of aDigital Magnetic Intensity Instrument

ASTM D6639-2001 地下勘察用頻域電磁法的標準指南

Standard Guide for Using the Frequency Domain Electromagnetic Method forSubsurface Investigations

ASTM E45 確定鋼中夾雜物含量的標準方法

ASTM E109-76 干粉法磁粉檢驗

ASTM E125-1997(2003) 鑄鐵件磁粉檢驗參考照片 Reference Photographsfor Magnetic Particle Indications on Ferrous Castings

ASTM E138-76 濕法磁粉檢驗

ASTM E215-2001 鋁合金無縫管電磁檢驗的標準化設備

Standardizing Equipment for Electromagnetic Examination of SeamlessAluminum-Alloy Tube

ASTM E243-2001 銅及銅合金管電磁(渦流) 檢測規程

Practice for Electromagnetic (Eddy-Current) Examination of Copper andCopper-Alloy Tubes

ASTM E268-84a 電磁檢測術語定義

ASTM E269-84a 磁粉檢驗術語定義

ASTM E309-95(2001) 鋼管制品磁飽和法渦流檢查規程

Eddy-Current Examination of Steel Tubular Products Using Magnetic Saturation

ASTM E376-2003 用磁場或渦流(電磁的)檢測法測量涂層厚度的規程

Practice for Measuring Coating Thickness by Magnetic-Field or Eddy-Current(Electromagnetic) Test Methods

ASTM E426-2001 奧氏體不銹鋼及類似合金無縫和焊接管制品的電磁(渦流) 檢驗

Electromagnetic (Eddy-Current) Examination of Seamless and Welded TubularProducts, Austenitic Stainless Steel and Similar Alloys

ASTM E566-2001 黑色金屬電磁(渦流)分選 Electromagnetic (Eddy-Current) Sorting of Ferrous Metals

ASTM E570-2001 鐵磁性鋼管制品漏磁檢驗的規程

Practice for Flux Leakage Examination of Ferromagnetic Steel Tubular Products

ASTM E571-2001 鎳和鎳合金管制品電磁(渦流) 檢驗

Electromagnetic (Eddy-Current) Examination of Nickel and Nickel Alloy TubularProducts

ASTM E690-2001 非磁性熱交換器管現場電磁(渦流)檢驗

In Situ Electromagnetic (Eddy-Current) Examination of Nonmagnetic HeatExchanger Tubes

ASTM E703-2001 有色金屬電磁(渦流)分選規程

Practice for Electromagnetic (Eddy-Current) Sorting of Nonferrous Metals

ASTM E709-2001 磁粉檢驗指南 Guide for Magnetic ParticleExamination

ASTM E977-2005 導電材料熱電分選技術規程

Practice for Thermoelectric Sorting of Electrically conductive Materials

ASTM E1004-2002 用電磁(渦流)法測定電導率的標準規程

Standard Practice for Determining Electrical Conductivity Using theElectromagnetic (Eddy-Current) Method

ASTM E1033-2001 居里點溫度以上用電磁(渦流)法檢查F 型連續焊(CW) 鐵磁性管的技術規程

Practice for Electromagnetic(Eddy-Current) Examination of Type F-ContinuouslyWelded(CW) Ferromagnetic Pipe and Tubing Above the Curie Temperature

ASTM E1312-2001 居里點溫度以上鐵磁性圓柱棒電磁(渦流) 檢查技術規程

Practice for Electromagnetic(Eddy-Current) Examination of FerromagneticCylindrical Bar Product Above the Curie Temperature

ASTM E1444-2005 磁粉檢驗標準規程 Standard Practice for MagneticParticle Examination

ASTM E1571-2001 鐵磁性鋼絲繩電磁檢驗規程

Practice for Electromagnetic Examination of Ferromagnetic Steel Wire Rope

ASTM E1606-2001 電工用銅質再拉棒電磁(渦流) 檢查技術規程

Practice for Electromagnetic(Eddy-Current) Examination of Copper Redraw Rod forElectrical Purposes

ASTM E1629-1996(2001) 測定絕對式渦流探頭阻抗的規程

Practice for Determining the Impedance of Absolute Eddy Current Probes

ASTM E2096-2005 使用遠場渦流技術現場檢查鐵磁性熱交換器管的技術規程

Practice for In Situ Examination of Ferromagnetic Heat-Exchanger Tubes UsingRemote Field Testing

ASTM E2261-2003 交流電場測量技術的焊縫檢測規程

Practice for Examination of Welds Using the Alternating Current FieldMeasurement Technique

ASTM E2297-2004 液體滲透和磁粉方法用UV-A與可見光源及強度計的指南

Guide for use of UV-A and Visible Light Sources and Meters used in the LiquidPenetrant and Magnetic Particle Methods

ASTM E2337-2004 互感電橋應用于鍋爐管壁測厚的指南

Guide for Mutual Inductance Bridge Applications for Wall ThicknessDeterminations in Boiler Tubing

ASTM E2338-2004 用不帶標準參考覆蓋層的適當渦流傳感器表征覆蓋層特性的規程

Practice for Characterization of Coatings Using Conformable Eddy-Current Sensorwithout Coating Reference Standards

ASTM F673-1990(1996) 用非接觸渦流儀測量半導體膜片電阻率的試驗方法(F-1)

Test Methods for Measuring Resistivity of Semiconductor Slices or SheetResistance of Semiconductor Films with a Noncontact Eddy-Current Gage

ASTM G96-90(1996) 固定設備在線腐蝕監測指南（電學和電磁學方法）

ASME Boiler & Pressure Vessel Code(ASME鍋爐壓力容器規范)第V卷《無損檢測》2004版，第7篇“磁粉檢測”

MIL-M-6867C-69 磁性檢驗設備

MIL-I-6868E-76 磁粉檢驗方法(INDT,85-4)

MIL-HDBK-728/4(92) 磁粉檢驗

MIL-HDBK-728/2(92) 渦流檢驗

MIL-STD-288(57) 測定變形奧氏體鋼磁導率的程序

MIL-STD-1537B(88) 用渦流電導率測試法檢驗鋁合金熱處理質量

MIL-STD-2032(90) 美國海軍艦船用熱交換器管渦流檢驗

MIL-M-6867C(69) 磁粉檢驗設備

MIL-I-83387A(87) 磁橡膠檢查方法

MIL-P-85585(82) 無屏蔽單線圈絕對測量的渦流探頭

BAC 5424 (美國波音公司)磁粉檢驗

BAC 5963 渦流檢驗

DPS 4.704 (美國麥道公司)磁粉檢驗

DPS 4.704-1 磁粉檢驗--返修

DPS 4.704-2 磁粉檢驗--適用性

DPS 1.05 渦流法測電導率--設備與方法

03014008發表于 2008-11-812:55

日本標準：

JIS C2501-1998 永久磁鐵試驗方法 Methods of test for permanentmagnet

JIS G 0565-1992 鐵磁性材料磁粉檢驗方法及磁粉顯示等級 (INDT,84-2 1982年版)

METHOD FOR MAGNETIC PARTICLE TESTING OF FERROMAGNETIC MATERIALS ANDCLASSIFICATION OF MAGNETIC PARTICLE INDICATION

JIS G 0568-1993 鋼制產品的環繞線圈法渦流檢測

Method for eddy current testing of steel products by encircling coil technique

JIS G 0583-2004 鋼管的渦流檢驗方法 Eddy current examination ofsteel pipes and tubes

JIS H 0502-1986 銅及銅合金管的渦流檢測方法

METHOD OF EDDY CURRENT TESTING FOR COPPER AND COPPER ALLOY PIPES AND TUBES

JIS H 0505-1975 有色金屬材料的電阻率及導電率測定方法

Measuring methods for electrical resistivity and conductivity of non-ferrousmaterials

JIS H 0515-1992 鈦管的渦流檢驗 Eddy current inspection oftitanium pipes and tubes

JIS H 0601:62 鍺的電阻率測定方法

JIS H 0602:95 硅單晶及硅薄片的四探針法電阻率測定方法

JIS Z 2314-1991 渦流試驗儀器性能特性試驗方法

Test methods for performance characteristics of eddy current testinginstruments

JIS Z 2315-1991 渦流探傷系統性能特性試驗方法

TEST METHODS FOR PERFORMANCE CHARACTERISTICS OF EDDY CURRENT FLAW DETECTINGSYSTEM

JIS Z 2319-1991 漏磁試驗方法 Methods for magnetic leakageflux testing

JIS Z 2321-1993 用于磁粉檢測的交流磁軛 AC YOKE MAGNET FOR MAGNETICPARTICLE TESTING

JIS Z 2340:2002 磁粉和滲透檢驗中目視校驗計較準方法的確認

Confirmation method of calibration by visual calibration gauge on magneticparticle and liquid penetrant testing

JIS Z 2343-3:2001 無損檢測滲透檢測第3部分：參考試塊

Non-destructive testing -- Penetrant testing -- Part 3: Reference test blocks

JIS Z 8202-5-2000 量值和單位第5部分:電學和磁學 Quantities and units - Part 5: Electricity and magnetism

JIS W 1202-1986 宇航用渦流法對鋁合金熱處理測量的電導試驗

Electrical conductivity test for measurement of heat treatment of aluminumalloys, eddy current method, for aerospace use

JIS W 4031-82 宇航用磁粉檢驗方法 INSPECTION PROCESS OF MAGNETICPARTICLE FOR AEROSPACE USE

NDIS 3101-84 渦流探傷裝置單項性能的測試及其表示方法

NDIS 3102-84 渦流探傷裝置綜合性能的測試及其表示方法

NDIS 3301-77 磁粉探傷用C1型標準試片

NDIS 3404-82 漏磁探傷測試方法(INDT,85-3)

NDIS 3105-83 交流磁軛磁粉檢驗裝置性能與試驗方法

NDIS 3403-81 表面缺陷檢測方法

03014008發表于 2008-11-812:55

德國標準：

DIN 50470-1980 永磁材料的檢測測定磁軛的退磁曲線和永磁導磁率感應法

Testing of permanent magnet materials; Determination of the demagnetizationcurve and permanent permeability in a yoke; Inductive method

DIN 50472-1981 永久磁鐵的檢測在工作范圍內測定磁通量值

Testing of permanent magnets; determination of the magnetic flux values in theworking range

DIN 50933-1987 用探針式差動測量器測量涂層厚度

Measurement of coating thickness by differential measurement using a stylusinstrument

DIN 50981-79 用磁粉法測量鐵素體材料非鐵磁性層的厚度

DIN 50984-78 用渦流法測量非鐵素體母材的非導電層厚度

DIN 50985-77 用電容法測量導電母材上非導電層的厚度

DIN 54121-65 磁粉探傷定義及檢驗證明

DIN 54130-1974 無損檢測漏磁檢測通則

Non-destructive testing; magnetic leakage flux testing, general

DIN 54131T1-84 除攜帶式以外的固定式與移動式磁粉檢驗設備性能及測定方法

DIN 54131T2-84 攜帶式磁粉檢驗設備性能及測定方法

DIN 54132-80 磁粉檢驗介質的性能測定

DIN 54136-1-1988 無損檢測帶掃描探頭的漏磁檢測原理

Non-destructive testing; magnetic leakage flux testing by scanning with probes;principles

DIN 54140-3-1989 無損檢測電磁法測試線圈組件的圖像和一般特性

Non-destructive testing; electromagnetic methods; representation and generalcharacteristics of test coil assemblies

DIN 54140T1-76 電磁(渦流)法檢測的一般規則

DIN 54140T2-84 電磁檢測名詞術語

DIN 54141-1-1982 無損檢測管子的渦流檢測用同心試驗線圈和單頻率法檢測的一般注意事項

Non-destructive testing; Eddy current testing of pipes and tubes; Generalremarks on testing using concentric test coils and the single-frequency method

DIN 54141-2-1982 無損檢測管子的渦流檢測同心試驗線圈的渦流檢測系統性能測定與校驗的參考方法Non-destructive testing; Eddy current testing of pipes and tubes; Referencemethod for the determination and calibration of the properties of an eddycurrent testing system using concentric test coils

DIN 54141-3-1987 無損檢測管子的渦流檢測方法

Non-destructive testing; eddy current testing of pipes and tubes; procedure

DIN 54141T1-82 穿過式線圈單頻法管材渦流檢測(NDT,86-1)

DIN 54141T2-82 穿過式線圈渦流檢驗裝置性能的測定方法

DIN 54141T3-85 渦流檢測的實施

DIN 25435T2-79 核技術設備定期磁粉檢驗

DIN V VDE V 0848-4/A3-1995 電磁場中的安全性在0至30KHz頻率范圍的人員防護修訂3

Safety in electromagnetic fields - Protection of persons in the frequency rangefrom 0 to 30 kHz; Amendment A3

DIN EN 1290-2002 焊縫的無損檢測焊縫的磁粉檢測

Non-destructive testing of welds - Magnetic particle testing of welds; Germanversion EN 1290:1998 + A1:2002

DIN EN 1291-2002 焊縫的無損檢測焊縫的磁粉檢測驗收等級

Non-destructive testing of welds - Magnetic particle testing of welds -Acceptance levels; German version EN 1291:1998 + A1:2002

DIN EN 1330-5-1998 無損檢測術語第5部分:渦流檢測

Non-destructive testing - Terminology - Part 5: Terms used in Eddy Currenttesting; trilingual version EN 1330-5:1998

DIN EN 1369-1997 鑄造磁粉檢驗 Founding - Magnetic particleinspection; German version EN 1369:1996

DIN EN 1971-1998 銅和銅合金管子的渦流檢測

Copper and copper alloys - Eddy current test for tubes; German version EN1971:1998

DIN EN 1711-2000 焊縫的無損檢驗焊縫的復平面分析渦流檢驗

Non-destructive examination of welds - Eddy current examination of welds bycomplex plane analysis; German version EN 1711:2000

DIN EN 10228-1-1999 鋼鍛件的無損檢測第1部分:磁粉檢驗

Non-destructive testing of steel forgings - Part 1: Magnetic particleinspection; German version EN 10228-1:1999

DIN EN 10246-1-1996 鋼管的無損檢測第1部分:驗證無縫和焊接鐵磁鋼管(埋弧焊除外)水壓密封性的自動電磁檢測 Non-destructive testing of steel tubes - Part 1: Automatic electromagnetictesting of seamless and welded (except submerged arc-welded) ferromagneticsteel tubes for verification of hydraulic leak-tightness; German version EN10246-1:1996

DIN EN 10246-3-2000 鋼管的無損檢測第3部分:探測無縫和焊接鋼管(埋弧焊接除外)不完整性的自動渦流檢測Non-destructivetesting of steel tubes - Part 3: Automatic eddy current testing of seamless andwelded (except submerged arc-welded) steel tubes for the detection ofimperfections; German version EN 10246-3:1999

DIN EN 10246-4-2000 鋼管的無損檢測第4部分:探測鐵磁無縫鋼管橫向不完整性的自動全圓周磁探頭/磁漏檢測 Non-destructive testing of steel tubes - Part 4: Automatic fullperipheral magnetic transducer/flux leakage testing of seamless ferromagneticsteel tubes for the detection of transverse imperfections; German version EN10246-4:1999

DIN EN 10246-5-2000 鋼管的無損檢測第5部分:探測無縫和焊接(埋弧焊接除外)鐵磁鋼管縱向不完整性的自動全圓周磁探頭/磁漏檢測 Non-destructive testing of steel tubes- Part 5: Automatic full peripheral magnetic transducer/flux leakage testing ofseamless and welded (except submerged arc-welded) ferromagnetic steel tubes forthe detection of longitudinal imperfections; German version EN 10246-5:1999

DIN EN 10246-18-2000 鋼管的無損檢測第18部分:探測無縫和焊接鐵磁鋼管管端層狀不完整性的磁粉檢驗 Non-destructivetesting of steel tubes - Part 18: Magnetic particle inspection of the tube endsof seamless and welded ferromagnetic steel tubes for the detection of laminarimperfections; German version EN 10246-18:2000

DIN EN 12084-2001 無損檢測渦流檢測一般原理和基本指南

Non-destructive testing - Eddy current testing - General principles and basicguidelines; German version EN 12084:2001

DIN EN 13860-1-2003 無損檢測渦流檢驗設備特性和驗證第1部分:儀器特性和驗證

Non-destructive testing - Eddy current examination; Equipment characteristicsand verification - Part 1: Instrument characteristics and verification; Germanversion EN 13860-1:2003

DIN EN 13860-2-2003 無損檢測渦流檢驗設備特性和驗證第2部分:探頭特性和驗證

Non-destructive testing - Eddy current examination; Equipment characteristicsand verification - Part 2: Probe characteristics and verification; Germanversion EN 13860-2:2003

DIN EN ISO 2178-1995 磁性基體上的非磁性涂鍍層涂鍍層厚度測量磁性法

Non-magnetic coatings on magnetic substrates - Measurement of coating thickness- Magnetic method (ISO 2178:1982); German version EN ISO 2178:1995

DIN EN ISO 2360-1995 非磁性基體金屬上的非導體涂層涂層厚度測量渦流法

Non-conductive coatings on non-magnetic basis metals - Measurement of coatingthickness - Eddy current method (ISO 2360:1982); German version EN ISO2360:1995

DIN EN ISO 2361-1995 磁性和非磁性基體上的鎳電鍍層鍍層厚度測量磁性法

Electrodeposited nickel coatings on magnetic and non-magnetic substrates -Measurement of coating thickness - Magnetic method (ISO 2361:1982); Germanversion EN ISO 2361:1995

DIN EN ISO 9934-1-2002 無損檢測磁粉檢測第1部分:一般原理

Non-destructive testing - Magnetic particle testing - Part 1: Generalprinciples (ISO 9934-1:2001); German version EN ISO 9934-1:2001

DIN EN ISO 9934-2-2003 無損檢測磁粉檢測第2部分:探測介質

Non-destructive testing - Magnetic particle testing - Part 2: Detection media(ISO 9934-2:2002); German version EN ISO 9934-2:2002

DIN EN ISO 9934-3-2002 無損檢測磁粉檢測第3部分:設備

Non-destructive testing - Magnetic particle testing - Part 3: Equipment (ISO9934-3:2002); German version EN ISO 9934-3:2002

03014008發表于 2008-11-812:57

英國標準：

BS 1881-204-1988 混凝土試驗-電磁式保護層厚度計應用的推薦方法

BS 3680/3H:1993 利用線圈全部長、寬的電磁方法

BS 3683-2-1985 無損檢測術語磁粉探傷

Glossary of terms used in non-destructive testing - Magnetic particle flawdetection

BS 3683 Pt.5-83 渦流檢測名詞術語

BS 3889 Pt.2A-86(1991) 管道和管子無損檢測方法鍛鋼管的渦流檢測

BS 3889 Pt.2B-82管道和管子無損檢測方法有色金屬管的渦流檢測

BS 4069-82 磁粉探傷用磁粉及磁懸液(INDT,84-2)

BS 4080/1: 用磁粉探傷顯示表面缺陷

BS 4397-69 焊縫的磁粉檢測方法(WSTS,85-4)

BS 4408 Pt.1-69 混凝土復蓋層的電磁測量方法

BS 4489:1984 無損檢測中評定黑光的方法

BS 5044-73(1987) 磁粉探傷用反差增強涂料

BS 5138-74(2000) 精加工整體鍛造及落錘鍛曲軸的磁粉檢驗

BS 5411 Pt.3-84 非磁性基體上非導電復蓋層厚度的渦流檢測

BS 5411 Pt.9-84 非磁性基體上鍍鎳層厚度的磁性檢測方法

BS 5411 Pt.11-84磁性基體上非磁性復蓋層厚度的磁性測量方法

BS 6072-81(1986) 缺陷的磁粉檢驗方法(81年版在INDT 84-2)

BS 6404-5-1995 磁性材料永磁(硬磁)材料磁性能測量方法

Magnetic materials - Permanent magnet (magnetically hard) materials - Methodsof measurement of magnetic properties

BS DD ENV 50166-1-1995 人體電磁場照射低頻(0 Hz 至 10 kHz)

Human exposure to electromagnetic fields - Low frequency (0 Hz to 10 kHz)

BS DD ENV 50166-2-1995 人體電磁場照射高頻(10 kHz 至 300 GHz)

Human exposure to electromagnetic fields - High frequency (10 kHz to 300 GHz)

BS M35 材料及工件的磁粉檢驗

BS EN 1290-1998 焊縫的無損檢驗焊縫的磁粉檢驗

Non-destructive examination of welds - Magnetic particle examination of welds

BS EN 1291-1998 焊縫的無損檢驗焊縫的磁粉檢驗驗收等級

Non-destructive examination of welds - Magnetic particle testing of welds -Acceptance levels

BS EN 1330-5-1998 無損檢測術語-渦流檢測Non-destructive testing - Terminology - Terms used in eddy current testing

BS EN 1369-1997 鑄造-磁粉檢驗Founding - Magnetic particle inspection

BS EN 10228-1-1999 鍛鋼件無損檢測-磁粉檢驗Non-destructive testing of steel forgings - Magnetic particle inspection

BS EN 10246-1-1996 鋼管的無損檢測-鐵磁性無縫與焊接（埋弧焊除外）鋼管驗證水壓試驗的自動電磁檢測

Non-destructive testing of steel tubes - Automatic electromagnetic testing ofseamless and welded (except submerged arc welded) ferromagnetic steel tubes forverification of hydraulic leak-tightness

BS EN 10246-2-2000 鋼管的無損檢測-奧氏體與奧氏體-鐵素體無縫與焊接（埋弧焊除外）鋼管驗證水壓試驗的自動渦流檢測

BS EN 10246-3-2000 鋼管的無損檢測-探測無縫與焊接（埋弧焊除外）鋼管不完整性的自動渦流檢測

Non-destructive testing of steel tubes - Automatic eddy current testing ofseamless and welded (except submerged arc-welded) steel tubes for the detectionof imperfections

BS EN 10246-4-2000 鋼管的無損檢測-鐵磁性無縫鋼管橫向不完整性自動全圓周磁探頭/漏磁檢測

Non-destructive testing of steel tubes - Automatic full peripheral magnetictransducer/flux leakage testing of seamless ferromagnetic steel tubes for thedetection of transverse imperfections

BS EN 10246-5-2000 鋼管的無損檢測-鐵磁性無縫與焊接（埋弧焊除外）鋼管縱向不完整性自動全圓周磁探頭/漏磁檢測 Non-destructive testing of steel tubes- Automatic full peripheral magnetic transducer/flux leakage testing ofseamless and welded (except submerged arc-welded) ferromagnetic steel tubes forthe detection of longitudinal imperfections

BS EN 10246-12-2000 鋼管的無損檢測探測無縫和焊接鐵磁鋼管表面不完整性的磁粉檢驗

Non-destructive testing of steel tubes - Magnetic particle inspection ofseamless and welded ferromagnetic steel tubes for the detection of surfaceimperfections

BS EN 10246-18-2000 鋼管的無損檢測探測無縫和焊接鐵磁鋼管管端層狀不完整性的磁粉檢驗

Non-destructive testing of steel tubes - Magnetic particle inspection of tubeends of seamless and welded ferromagnetic steel tubes for the detection oflaminar imperfections

BS EN 12084-2001 無損檢測-渦流檢測-一般原理與指南

Non-destructive testing - Eddy current testing - General principles andguidelines

BS EN ISO 2178-1995 磁性基體上非磁性涂層的厚度測量-磁性法

Non-magnetic coatings on magnetic substrates - Measurement of coating thickness- Magnetic method

BS EN ISO 2360-1995 非磁性金屬基體上非導電涂層的厚度測量-渦流法

Non-conductive coatings on non-magnetic basis metals - Measurement of coatingthickness - Eddy current method

BS EN ISO 2361-1995 磁性和非磁性基體上鎳鍍層的厚度測量-磁性法

Electrodeposited nickel coatings on magnetic and non-magnetic substrates -Measurement of coating thickness - Magnetic method

BS EN ISO 9934-1-2001 無損檢測磁粉檢測一般原理 Non-destructivetesting - Magnetic particle testing - General principles

BS EN ISO 9934-2-2002 無損檢測磁粉檢測探測介質 Non-destructive testing -Magnetic particle testing - Detection media

BS EN ISO 9934-3-2002 無損檢測磁粉檢測設備 Non-destructive testing -Magnetic particle testing - Equipment

03014008發表于 2008-11-812:58

法國標準：

NF A04-101-64 冶金產品磁粉檢測(磁懸液檢測)

NF A04-121-74 鋼制長條形制品表面缺陷的磁粉檢驗

NF A04-193-1997 鑄造磁粉檢驗 Founding - Magnetic particleinspection.

NF A05-115-1999 銅及銅合金管子的渦流檢測 Copper and copper alloys.Eddy current test for tubes.

NF A09-020-5-1998 無損檢測術語第5部分:渦流檢測

Non-destructive testing. Terminology. Part 5 : terms used in Eddy Currenttesting.

NF A09-125-82 冶金制件磁粉探傷的一般原理

NF A09-160-2001 無損檢測渦流檢測一般原理和指南

Non-destructive testing - Eddy current testing - General principles andguidelines.

NF A09-590-1-2002 無損檢測磁粉檢測第1部分:一般原理

Non-destructive testing - Magnetic particle testing - Part 1 : generalprinciple.

NF A09-590-3-2002 無損檢測磁粉檢測第3部分：設備

Non-destructive testing - Magnetic particle testing - Part 3 : equipment.

NF A49-871-81 鐵磁性鋼管縱向缺陷的探頭檢漏法檢測

NF A49-872-83 穿過式線圈法的鋼管渦流探傷

NF A49-875-1-1996 鋼管的無損檢測第1部分:無縫和焊接鐵磁鋼管(埋弧焊除外)驗證水壓試驗的自動電磁檢測Non destructive testing of steels tubes. Part 1 : automatic electromagnetictesting of seamless and welded (except submerged arc welded) ferromagneticsteel tubes for verification of hydraulic leak-tightness.

NF A49-875-2-2000 鋼管的無損檢測第2部分:無縫和焊接奧氏體和奧氏體鐵素體鋼管(埋弧焊除外)驗證水壓試驗的自動渦流檢測Non-destructive testing of steel tubes - Part 2 : automatic eddy currenttesting of seamless and welded (except submerged arc-welded) austenitic andaustenitic-ferritic steel tubes for verification of hydraulic leak-tightness.

NF A49-875-3-2000 鋼管的無損檢測第3部分:探測無縫和焊接鋼管(埋弧焊除外)不完整性的自動渦流檢測Non-destructive testing of steel tubes - Part 3 : automatic eddy currenttesting of seamless and welded (except submerged arc-welded) steel tubes forthe detection of imperfections.

NF A49-875-4-2000 鋼管的無損檢測第4部分:探測無縫鐵磁鋼管橫向不完整性的自動全圓周磁探頭/磁漏檢測 Non-destructive testing of steel tubes- Part 4 : automatic full peripheral magnetic transducer/flux leakage testingof seamless ferromagnetic steel tubes for the detection of transverseimperfections.

NF A49-875-5-2000 鋼管的無損檢測第5部分:探測無縫和焊接(除埋弧焊)鐵磁鋼管縱向不完整性的自動全圓周磁探頭/漏磁檢測 Non-destructive testing of steel tubes- Part 5 : automatic full peripheral magnetic transducer/flux leakage testingof seamless and welded (except submerged arc welded) ferromagnetic steel tubes forthe detection of longitudinal imperfections.

NF A49-875-12-2000 鋼管的無損檢測第12部分:探測無縫和焊接鐵磁鋼管表面不完整性的磁粉檢驗

Non-destructive testing of steel tubes - Part 12 : magnetic particle inspectionof seamless and welded ferromagnetic steel tubes for the detection of surfaceimperfections.

NF A49-875-18-2000 鋼管的無損檢測第18部分:探測無縫和焊接鐵磁鋼管管端層狀不完整性的磁粉檢驗 Non-destructive testing of steel tubes - Part 18 : magneticparticle inspection of tube ends of seamless and welded ferromagnetic steeltubes for the detection of laminar imperfections.

NF A89-550-1998 焊縫的無損檢驗焊縫的磁粉檢驗

Non-destructive examination of welds - Magnetic particle examination of welds.

NF A89-550/A1-2002 焊縫的無損檢測焊縫的磁粉檢測

Non-destructive testing of welds - Magnetic particle testing of welds.

NF A89-551-1998 焊縫的無損檢驗焊縫的磁粉檢測驗收等級

Non-destructive examination of welds - Magnetic particle testing of welds -Acceptance levels.

NF A89-551/A1-2002 焊縫的無損檢測焊縫的磁粉檢測驗收等級

Non-destructive testing of welds - Magnetic particle testing of welds -Acceptance levels.

NF A91-112-1995 磁性基體上的非磁性涂層涂層厚度測量磁性法

Non-magnetic coatings on magnetic substrates. Measurement of coating thickness.Magnetic method.

NF A91-113-1995 非磁性基體金屬上的非導電涂層涂層厚度測量渦流法

Non-conductive coatings on non-magnetic basis metals. Measurement of coatingthickness. Eddy current method.